Step by Step Procedure for Applying Tint to Virgin Hair: Application, Removal & Care

Historically, the earliest recorded instances of hair coloring involved dyeing with plant-based products. Henna was the most commonly used vegetable tints are a type of hair coloring derived from plant sources. 

Plant-based methods are still used today, despite being messy and time-consuming. Plant extracts deposit on the hair's surface and generally preclude the use of other types of chemical services.

The primary penetrating agent in modern permanent hair color is an oxidation tint. Derived from coal tar, these tint molecules combine with a developer to form large molecules within the hair's cortex layer.

These dyes can both lift (lighten) and deposit (add color), resulting in a virtually endless range of shades. 

Procedure for applying tint to virgin hair

The following are the step by step procedure for applying tint to Virgin hair:

1.Have your client sit comfortably and drape her.

2.Check the patch test results for any signs of redness or irritation. Apply only to cleansed skin.

3.Shampooing is necessary, or as directed by your instructor or the manufacturer. Use caution; avoid any scalp manipulation during shampooing.

4.Apply a conditioning treatment as your analysis revealed. Ask your instructor if a clarifying treatment should be given to neutralize any coating or chemical buildup on the hair cuticle.

5.Perform a strand test as directed.

6.Part hair into four equal sections. 

7.Apply protective cream around the hairline and above the ears.

8.Wear protective gloves.

9.Mix the formula according to the results and manufacturer's instructions. 

10.Apply the tint, starting with the most resistant area.

• a.If you're going lighter, this will be the darkest area. Start applying at the mid-shaft.
• b.If you're going darker, this will be the lightest, or grayest, area. Begin application at the scalp, outlining the first section 1/2-inch from the parting.

11.Horizontal subdivisions Apply color to the mid-shaft area, starting 1/2 inch from the scalp (at the scalp if going darker) and continuing to the porous ends, but not through.

12.Lift the subdivision (section) up and apply to the lower part of the hair. Move the hair toward the crown and proceed to the next 1/2-inch subdivision.

13.Work quickly and rhythmically for best results. Lift the hair from the scalp and gently flip the section back. Avoid packing the hair onto the scalp.

14.Quickly move on to the next section, highlighting that the application is getting darker.

15.Apply the color, lift the hair up from the scalp, and flip it back to its original position. 

16.Set your timer according to the results of your strand test.

17.Cross-check each section by gently parting it vertically and adding more color formula as needed. 

18.When cross-checking, make sure the color doesn't come into contact with the scalp. If this happens, gently wipe it off with a damp towel.

19.Check the time by removing the color from the hairline five minutes before the timer indicates. Rinse the hairline with water and towel dry to evaluate the results. If the color isn't complete, re-saturate the hairline and continue timing.

20.When the center strand (lightening) has developed according to your strand test results, apply the color to the scalp area up to the mid-shaft.

21.Again, work the tint formula through the ends and time according to your strand test results.

22.Take a final strand test to confirm your timing and desired results.

 Procedure for removing tint from virgin hair

When you are sure the strand test indicates the desired color, remove the color from the hair.

The following procedure for removing tint from virgin hair:

1.Shampoo bowl with the client, with lukewarm to warm water.

2.Emulsify the color by massaging with the palms of your hands and Rinse thoroughly.

3.Pour a small amount of acid-balanced (pH 3.8-4.5) shampoo into the palm of your hand. Shampoo with your hands and apply to the client's hair.

4.Starting at the hairline, massage gently, working your fingers down the hairline to avoid tangles. 

5.Repeat as needed until all excess color and protective cream is removed from the hair and scalp.

6.Towel to absorb excess moisture. 

7.Moisten hair and Work the product through hair and time as directed.

8.Wash without soap and towel dry.

9.Moisturize according to your hair analysis.

10. Make all notations on the client record card. 

11. Towel blot and proceed with styling. If you decide to thermally style your hair, use a low heat setting and apply less tension to your brush. 

12 Recommend suitable retail products to maintain the client's hair in excellent condition at home.

13.After that Clean the work areas.

Advantages of Tints

The following advantages of tints:

1.Any natural shade can be replicated. These colors are permanent, and visible enhancement requires a correction that won't become apparent for a month or more.

2. Tints can lift or deposit, allowing you to give clients any desired result.

3.Tints can completely cover gray to any degree.

4.Hair is not coated and can receive other chemical treatments.

5.Because the color penetrate the cortex layer of the hair, the color results appear very natural.

Disadvantages of Tints

The following disadvantage of tints:

1.A fast test should be given before each application.

2.Hair undergoes a chemical change, requiring careful maintenance and repair.

3.The hair's natural pigment changes.  In most cases, the pigment is lifted. Over time, the hair may fade.

4.To remove the tint effect, you must use a tinter (which can also lighten the natural pigment), retinto the camouflage effect, or cut the hair to remove the dyed portion.

5.Hair color can fade with time and shampooing, becoming off-color or harsh tones.